ftp.cc.uoc.gr
rfc5233
This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 3079
Network Working Group                                       K. Murchison
Request for Comments: 5233                    Carnegie Mellon University
Obsoletes: 3598                                             January 2008
Category: Standards Track


              Sieve Email Filtering: Subaddress Extension

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   On email systems that allow for 'subaddressing' or 'detailed
   addressing' (e.g., "ken+sieve@example.org"), it is sometimes
   desirable to make comparisons against these sub-parts of addresses.
   This document defines an extension to the Sieve Email Filtering
   Language that allows users to compare against the user and detail
   sub-parts of an address.

Table of Contents

   1. Introduction ....................................................2
   2. Conventions Used in This Document ...............................2
   3. Capability Identifier ...........................................2
   4. Subaddress Comparisons ..........................................2
   5. IANA Considerations .............................................5
   6. Security Considerations .........................................5
   7. Normative References ............................................5
   Appendix A. Acknowledgments ........................................6
   Appendix B. Changes since RFC 3598 .................................6

1.  Introduction

   Subaddressing is the practice of augmenting the local-part of an
   [RFC2822] address with some 'detail' information in order to give
   some extra meaning to that address.  One common way of encoding
   'detail' information into the local-part is to add a 'separator
   character sequence', such as "+", to form a boundary between the
   'user' (original local-part) and 'detail' sub-parts of the address,
   much like the "@" character forms the boundary between the local-part
   and domain.

   Typical uses of subaddressing might be:

   o  A message addressed to "ken+sieve@example.org" is delivered into a
      mailbox called "sieve" belonging to the user "ken".

   o  A message addressed to "5551212#123@example.com" is delivered to
      the voice mailbox number "123" at phone number "5551212".

   This document describes an extension to the Sieve language defined by
   [RFC5228] for comparing against the 'user' and 'detail' sub-parts of
   an address.

2.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Capability Identifier

   The capability string associated with the extension defined in this
   document is "subaddress".

4.  Subaddress Comparisons

   Test commands that act exclusively on addresses may take the optional
   tagged arguments ":user" and ":detail" to specify what sub-part of
   the local-part of the address will be acted upon.

      NOTE: In most cases, the envelope "to" address is the preferred
      address to examine for subaddress information when the desire is
      to sort messages based on how they were addressed so as to get to
      a specific recipient.  The envelope address is, after all, the
      reason a given message is being processed by a given sieve script
      for a given user.  This is particularly true when mailing lists,
      aliases, and 'virtual domains' are involved since the envelope may
      be the only source of detail information for the specific
      recipient.

      NOTE: Because the encoding of detailed addresses are site and/or
      implementation specific, using the subaddress extension on foreign
      addresses (such as the envelope "from" address or originator
      header fields) may lead to inconsistent or incorrect results.

   The ":user" argument specifies the user sub-part of the local-part of
   an address.  If the address is not encoded to contain a detail sub-
   part, then ":user" specifies the entire left side of the address
   (equivalent to ":localpart").

   The ":detail" argument specifies the detail sub-part of the local-
   part of an address.  If the address is not encoded to contain a
   detail sub-part, then the address fails to match any of the specified
   keys.  If a zero-length string is encoded as the detail sub-part,
   then ":detail" resolves to the empty value ("").

      NOTE: If the encoding method used for detailed addresses utilizes
      a separator character sequence, and the separator character
      sequence occurs more than once in the local-part, then the logic
      used to split the address is implementation-defined and is usually
      dependent on the format used by the encompassing mail system.

   Implementations MUST make sure that the encoding method used for
   detailed addresses matches that which is used and/or allowed by the
   encompassing mail system, otherwise unexpected results might occur.
   Note that the mechanisms used to define and/or query the encoding
   method used by the mail system are outside the scope of this
   document.

   The ":user" and ":detail" address parts are subject to the same rules
   and restrictions as the standard address parts defined in [RFC5228],
   Section 2.7.4.

   For convenience, the "ADDRESS-PART" syntax element defined in
   [RFC5228], Section 2.7.4, is augmented here as follows:

         ADDRESS-PART  =/  ":user" / ":detail"

      A diagram showing the ADDRESS-PARTs of an email address where the 
   detail information follows a separator character sequence of "+" is
   shown below:

          :user "+" :detail  "@" :domain
         \-----------------/
             :localpart

   A diagram showing the ADDRESS-PARTs of an email address where the
   detail information precedes a separator character sequence of "--" is
   shown below:

          :detail "--" :user  "@" :domain
         \------------------/
             :localpart
EID 3079 (Verified) is as follows:

Section: 4

Original Text:

   A diagram showing the ADDRESS-PARTs of an email address where the
   detail information follows a separator character sequence of "+" is
   shown below:

          :user "+" :detail  "@" :domain
         \-----------------/
             :local-part

   A diagram showing the ADDRESS-PARTs of a email address where the
   detail information precedes a separator character sequence of "--" is
   shown below:

          :detail "--" :user  "@" :domain
         \------------------/
             :local-part

Corrected Text:

   A diagram showing the ADDRESS-PARTs of an email address where the
   detail information follows a separator character sequence of "+" is
   shown below:

          :user "+" :detail  "@" :domain
         \-----------------/
             :localpart

   A diagram showing the ADDRESS-PARTs of an email address where the
   detail information precedes a separator character sequence of "--" is
   shown below:

          :detail "--" :user  "@" :domain
         \------------------/
             :localpart
Notes:
Throughout the document, the prose phrase "local-part" is hyphenated, while the syntactic word ":localpart" is not hyphenated. Also, correct "a email address" to "an email address"
Example (where the detail information follows "+"): require ["envelope", "subaddress", "fileinto"]; # In this example the same user account receives mail for both # "ken@example.com" and "postmaster@example.com" # File all messages to postmaster into a single mailbox, # ignoring the :detail part. if envelope :user "to" "postmaster" { fileinto "inbox.postmaster"; stop; } # File mailing list messages (subscribed as "ken+mta-filters"). if envelope :detail "to" "mta-filters" { fileinto "inbox.ietf-mta-filters"; } # Redirect all mail sent to "ken+foo". if envelope :detail "to" "foo" { redirect "ken@example.net"; } 5. IANA Considerations The following template specifies the IANA registration of the subaddress Sieve extension specified in this document. This registration replaces that from RFC 3598: To: iana@iana.org Subject: Registration of new Sieve extension Capability name: subaddress Description: Adds the ':user' and ':detail' address parts for use with the address and envelope tests RFC number: RFC 5233 Contact address: The Sieve discussion list <ietf-mta-filters@imc.org> This information has been added to the list of Sieve extensions given on http://www.iana.org/assignments/sieve-extensions. 6. Security Considerations Security considerations are discussed in [RFC5228]. It is believed that this extension does not introduce any additional security concerns. 7. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2822] Resnick, P., "Internet Message Format", RFC 2822, April 2001. [RFC5228] Guenther, P., Ed., and T. Showalter, Ed., "Sieve: An Email Filtering Language", RFC 5228, January 2008. Appendix A. Acknowledgments Thanks to Tim Showalter, Alexey Melnikov, Michael Salmon, Randall Gellens, Philip Guenther, Jutta Degener, Michael Haardt, Ned Freed, Mark Mallett, and Barry Leiba for their help with this document. Appendix B. Changes since RFC 3598 o Discussion of how the user and detail information is encoded now uses generic language. o Added note detailing that this extension is most useful when used on the envelope "to" address. o Added note detailing that this extension isn't very useful on foreign addresses (envelope "from" or originator header fields). o Fixed envelope test example to only use "to" address. o Replaced ":user" example with one that doesn't produce unexpected behavior. o Refer to the zero-length string ("") as "empty" instead of "null" (per RFC 5228). o Use only RFC 2606 domains in examples. o Miscellaneous editorial changes. Author's Address Kenneth Murchison Carnegie Mellon University 5000 Forbes Avenue Cyert Hall 285 Pittsburgh, PA 15213 USA Phone: +1 412 268 2638 EMail: murch@andrew.cmu.edu Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.