ftp.cc.uoc.gr
rfc6003
This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 2551, EID 2552
Internet Engineering Task Force (IETF)                  D. Papadimitriou
Request for Comments: 6003                                Alcatel-Lucent
Updates: 3471, 3473                                         October 2010
Category: Standards Track
ISSN: 2070-1721


                      Ethernet Traffic Parameters

Abstract

   This document describes the support of Metro Ethernet Forum (MEF)
   Ethernet traffic parameters as described in MEF10.1 when using
   Generalized Multi-Protocol Label Switching (GMPLS) Resource
   ReSerVation Protocol - Traffic Engineering (RSVP-TE) signaling.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6003.

Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

1.  Introduction

   Per [RFC3471], Generalized Multi-Protocol Label Switching (GMPLS)
   allows the inclusion of technology-specific parameters in signaling.
   This document introduces Ethernet SENDER_TSPEC and FLOWSPEC-specific
   objects in support of Metro Ethernet Forum (MEF) Ethernet traffic
   parameters as specified in [MEF10.1] and ITU-T Ethernet Service
   Switching as discussed in [RFC6004].  For example:

   o  For Ethernet Private Line (EPL) services [MEF6], these traffic
      parameters are applicable to each Ethernet Virtual Connection
      (EVC) crossing a given port.

   o  For Ethernet Virtual Private Line (EVPL) services [MEF6], these
      traffic parameters are applicable per Ethernet Virtual Connection
      (EVC) with a single or multiple Class of Service (CoS),
      independent of its associated Virtual LAN ID (VID) or set of VIDs.

      Association between EVC and VIDs is detailed in [MEF10.1].  The
      format and encoding of the VID (or set of VIDs) is documented in a
      companion document [RFC6004].

   This does not preclude broader usage of the Ethernet SENDER_TSPEC and
   FLOWSPEC-specific objects specified this document.  For instance,
   they may also be used for signaling Ethernet Label Switched Paths
   (LSPs), in the Generalized Label Request (see [RFC3471]), the
   Switching Type field is set to Layer 2 Switching Capability (L2SC)
   and the LSP Encoding Type field to Ethernet.

2.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

   Moreover, the reader is assumed to be familiar with the terminology
   in [MEF10.1] as well as in [RFC3471] and [RFC3473].

3.  Overview

   In GMPLS RSVP-TE [RFC3473], the SENDER_TSPEC object is used on a Path
   message to indicate the bandwidth that is requested for the LSP being
   established, and the FLOWSPEC object is used on a Resv message to
   indicate the bandwidth actually reserved for the LSP.  The Ethernet
   SENDER_TSPEC/FLOWSPEC object includes the Ethernet link type
   (switching granularity) of the requested LSP and the MTU value for

   the LSP.  Other information about the requested bandwidth
   characteristics of the LSP are carried in the Bandwidth Profile as a
   TLV within the Ethernet SENDER_TSPEC/FLOWSPEC object.

   The Ethernet SENDER_TSPEC/FLOWSPEC object includes the Ethernet link
   type (switching granularity) of the requested LSP and the MTU value
   for the LSP.

   The Bandwidth Profile defines the set of traffic parameters
   applicable to a sequence of Service Frames, referred to as bandwidth
   profile parameters (as specified in [MEF10.1]):

   o  Committed Rate: indicates the rate at which traffic commits to be
      sent to the Ethernet LSP.  The committed rate is described in
      terms of the CIR (Committed Information Rate) and CBS (Committed
      Burst Size) traffic parameters.

      o  CIR is defined as the average rate (in bytes per unit of time)
         up to which the network is committed to transfer frames and
         meets its performance objectives.

      o  CBS defines a limit on the maximum number of information units
         (e.g., bytes) available for a burst of frames sent at the
         interface speed to remain CIR-conformant.

   o  Excess Rate: indicates the extent by which the traffic sent on an
      Ethernet LSP exceeds the committed rate.  The Excess Rate is
      described in terms of the EIR (Excess Information Rate) and EBS
      (Excess Burst Size) traffic parameters.

      o  EIR is defined as the average rate (in bytes per unit of time),
         in excess of the CIR, up to which the network may transfer
         frames without any performance objectives.

      o  EBS defines a limit on the maximum number of information units
         (e.g., bytes) available for a burst of frames sent at the
         interface speed to remain EIR-conformant.

   o  Color mode (CM): indicates whether the "color-aware" or "color-
      blind" property is employed by the bandwidth profile.

   o  Coupling flag (CF): allows the choice between two modes of
      operation of the rate enforcement algorithm.

4.  Ethernet SENDER_TSPEC Object

   The Ethernet SENDER_TSPEC object (Class-Num = 12, Class-Type = 6) has
   the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Length             | Class-Num (12)|   C-Type (6)  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Switching Granularity     |              MTU              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                              TLVs                             ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Switching Granularity (SG): 16 bits

      This field indicates the type of link that comprises the requested
      Ethernet LSP.

      The permitted Ethernet Link Type values are:

         Value   Switching Granularity
         -----   ---------------------
           0     Provided in signaling.  See [RFC6004].
           1     Ethernet Port (for port-based service)
           2     Ethernet Frame (for EVC-based service)
         255     Reserved

      Values 0 to 2 are specified by the present document.  Values 3
      through 239 are to be assigned by IANA via Standards Action
      [RFC5226].  Value 255 is reserved by the present document (its
      Length is to be determined by the RFC that will specify it).

      Values 240 through 254 are reserved for vendor-specific use.

      Values 256 through 65535 are not assigned at this time.

   MTU: 16 bits

      This is a two-octet value indicating the MTU in octets.

      The MTU field MUST NOT take a value smaller than 46 bytes for
      Ethernet v2 [ETHv2] and 38 bytes for IEEE 802.3 [IEEE802.3].

   TLV (Type-Length-Value):

      The Ethernet SENDER_TSPEC object MUST include at least one TLV and
      MAY include more than one TLV.

      Each TLV MUST have the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |             Length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                             Value                             ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type: 16 bits 

      Defined values are:

      Type     Length   Format            Description
      ------------------------------------------------------
        0         -     Reserved          Reserved value
        1         -     Reserved          Reserved value
       2        24     see Section 4.1   Ethernet Bandwidth
                                          Profile [MEF10.1]
        3         8     [RFC6004]         Layer 2 Control
                                          Protocol (L2CP)
      255         -     Reserved          Reserved value
EID 2551 (Verified) is as follows:

Section: 4, pg. 5

Original Text:

   Type: 16 bits

      Defined values are:

      Type     Length   Format            Description
      ------------------------------------------------------
        0         -     Reserved          Reserved value
        1         -     Reserved          Reserved value
|       2        24     see Section 3.1   Ethernet Bandwidth
                                          Profile [MEF10.1]
        3         8     [RFC6004]         Layer 2 Control
                                          Protocol (L2CP)
      255         -     Reserved          Reserved value

Corrected Text:

   Type: 16 bits

      Defined values are:

      Type     Length   Format            Description
      ------------------------------------------------------
        0         -     Reserved          Reserved value
        1         -     Reserved          Reserved value
|       2        24     see Section 4.1   Ethernet Bandwidth
                                          Profile [MEF10.1]
        3         8     [RFC6004]         Layer 2 Control
                                          Protocol (L2CP)
      255         -     Reserved          Reserved value
Notes:
Incorrect internal reference.
Values 0, 1, and 255 are reserved by the present document. Values 2 and 3 are specified by the present document. Values 4 through 239 are to be assigned by IANA via Standards Action [RFC5226]. Values 240 through 254 are reserved for vendor-specific use. Values 256 through 65535 are not assigned at this time. Length: 16 bits Indicates the length in bytes of the whole TLV including the Type and Length fields. A value field whose length is not a multiple of four MUST be zero-padded (with trailing zeros) so that the TLV is four-octet aligned. 4.1. Ethernet Bandwidth Profile TLV
EID 2552 (Verified) is as follows:

Section: 4.1, pg.7

Original Text:

   Index: 8 bits

      [...]

      A given index value j can be associated to at most N Class-Type
      values CTi (i =< N) of the EXTENDED_CLASSTYPE object.  This
|     association applies when a set of one or more CTIs maps to a
      single (shared) BW profile.  An example of value setting consists
      in assigning an arbitrary value comprised within the range
      [0x08,0xF8] associated to a set of CTi, the values in the range
|     [0xF8,0xFF] being selected for reserved sets.  This allows mapping
      to one of 248 predefined CTi sets.

Corrected Text:

   Index: 8 bits

      [...]

      A given index value j can be associated to at most N Class-Type
      values CTi (i =< N) of the EXTENDED_CLASSTYPE object.  This
|     association applies when a set of one or more CTis maps to a
      single (shared) BW profile.  An example of value setting consists
      in assigning an arbitrary value comprised within the range
      [0x08,0xF8] associated to a set of CTi, the values in the range
|     [0xF9,0xFF] being selected for reserved sets.  This allows mapping
      to one of 248 predefined CTi sets.
Notes:
Rationale:
a) consistent use of "CTi" -- 'i' essentially is a subscript index;
b) avoid ambiguity due to overlap in ranges given

[The first item is Editorial, but the second one clearly Technical]
The Type 2 TLV specifies the Ethernet Bandwidth Profile (BW profile). It defines an upper bound on the volume of the expected service frames belonging to a particular Ethernet service instance. The Ethernet SENDER_TSPEC object MAY include more than one Ethernet Bandwidth Profile TLV. The Type 2 TLV has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Profile | Index | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CIR | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CBS | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | EIR | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | EBS | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Profile: 8 bits This field is defined as a bit vector of binary flags. The following flags are defined: Flag 1 (bit 0): Coupling Flag (CF) Flag 2 (bit 1): Color Mode (CM) Where bit 0 is the low order bit. Other flags are reserved, they SHOULD be set to zero when sent, and SHOULD be ignored when received. A flag is set to value 1 to indicate that the corresponding metering profile is requested. The Flag 1 (CF) allows the choice between two modes of operation of the rate enforcement algorithm. The Flag 2 (CM) indicates whether the color-aware or color-blind property [MEF10.2] is employed by the bandwidth profile. When Flag 2 is set to value 0 (1), the bandwidth profile algorithm is said to be in color-blind (color-aware) mode. Index: 8 bits The Index field is used to reference bandwidth allocated for a given traffic class in case a multiple-class LSP is being requested. The Index field value MUST correspond to at least one of the Class-Type values included either in the CLASSTYPE object [RFC4124] or in the EXTENDED_CLASSTYPE object [MCOS]. A given index value j can be associated to at most N Class-Type values CTi (i =< N) of the EXTENDED_CLASSTYPE object. This association applies when a set of one or more CTIs maps to a single (shared) BW profile. An example of value setting consists in assigning an arbitrary value comprised within the range [0x08,0xF8] associated to a set of CTi, the values in the range [0xF8,0xFF] being selected for reserved sets. This allows mapping to one of 248 predefined CTi sets. A given index value j can be associated to a single CTi (1:1 correspondence). In this case, the index value setting consists in assigning the 3 least significant bits of the Index field itself to the CTi value itself (comprised in the range [0x00,0x07]). This applies in case a single CTi maps a single (dedicated) BW profile or multiple (dedicated) BW profiles. In the former case, the Ethernet SENDER_TSPEC object includes a single Ethernet Bandwidth Profile TLV. In the latter case, the Ethernet SENDER_TSPEC includes a set of more than one Ethernet Bandwidth Profile TLVs (whose respective index value is associated to a single CTi value). Note that the current specification allows for combining shared and dedicated BW profiles to the same LSP. That is, an Ethernet SENDER_TSPEC object MAY include multiple Ethernet Bandwidth Profile TLVs whose respective index can be associated on a 1:1 basis to a single CTi or to a set of multiple CTis. For each subobject of the EXTENDED_CLASSTYPE object [MCOS]: o Each CTi value SHOULD correspond 1:1 to the MEF Customer Edge VLAN CoS (CE-VLAN CoS). o The BW requested per CTi field MAY be used for bandwidth accounting purposes. By default, the value of the Index field MUST be set to 0. Reserved: 16 bits These bits SHOULD be set to zero when sent and MUST be ignored when received. CIR (Committed Information Rate): 32 bits The value of the CIR is in units of bytes per second. The CIR is encoded as a 32-bit IEEE single-precision floating-point number (see [RFC4506]). The CIR value MUST be greater than or equal to 0. CBS (Committed Burst Size): 32 bits The value of the CBS is in units of bytes. The CBS is encoded as a 32-bit IEEE single-precision floating-point number (see [RFC4506]). When CIR is strictly greater than 0 (CIR > 0), the CBS MUST be greater than or equal to the maximum frame size. EIR (Excess Information Rate): 32 bits The value of the EIR is in units of bytes per second. The EIR is encoded as a 32-bit IEEE single-precision floating-point number (see [RFC4506]). The EIR value MUST be greater than or equal to 0. EBS (Excess Burst Size): 32 bits The value of the EBS is in units of bytes. The EBS is encoded as a 32-bit IEEE single-precision floating-point number (see [RFC4506]). When EIR is strictly greater than 0 (EIR > 0), the EBS MUST be greater than or equal to the maximum frame size. 5. Ethernet FLOWSPEC Object The Ethernet FLOWSPEC object (Class-Num = 9, Class-Type = 6) has the same format as the Ethernet SENDER_TSPEC object. 6. Ethernet ADSPEC Object There is no ADSPEC object associated with the Ethernet SENDER_TSPEC object. Either the ADSPEC object is omitted or an IntServ ADSPEC with the Default General Characterization Parameters and Guaranteed Service fragment is used, see [RFC2210]. 7. Processing The Ethernet SENDER_TSPEC and FLOWSPEC objects specified in this document MAY be used for signaling Ethernet LSP. For signaling such an LSP, in the Generalized LABEL_REQUEST object (see [RFC3471]), the Switching Type field MUST be set to the value 51 (L2SC) and the LSP Encoding Type field MUST be set to the value 2 (Ethernet). The Ethernet SENDER_TSPEC object carries the traffic specification generated by the RSVP session sender. The Ethernet SENDER_TSPEC object SHOULD be forwarded and delivered unchanged to both intermediate and egress nodes. The Ethernet FLOWSPEC object carries reservation request information generated by receivers. As with any FLOWSPEC object, the Ethernet FLOWSPEC object flows upstream toward the ingress node. Intermediate and egress nodes MUST verify that the node itself and the interfaces on which the LSP will be established can support the requested Switching Granularity, MTU and values included in subobject TLVs. These nodes MUST be configured with the same predefined CT sets as the index value signaled as part of the Index field of the Ethernet Bandwidth Profile TLV (see Section 4.1). If the requested value(s) cannot be supported, the receiver node MUST generate a PathErr message with the error code "Traffic Control Error" and the error value "Service unsupported" (see [RFC2205]). In addition, if the MTU field is received with a value smaller than the minimum transfer unit size of the Ethernet frame (e.g., 46 bytes for Ethernet v2, 38 bytes for IEEE 802.3), the node MUST generate a PathErr message with the error code "Traffic Control Error" and the error value "Bad Tspec value" (see [RFC2205]). Error processing of the CLASSTYPE object follows rules defined in [RFC4124]. Error processing of the EXTENDED_CLASSTYPE object follows rules defined in [MCOS]. Moreover, a Label Switching Router (LSR) receiving a Path message with the EXTENDED_CLASSTYPE object, which recognizes the object and the particular Class-Type but does detect a mismatch in the index values, MUST send a PathErr message towards the sender with the error code "Extended Class-Type Error" and the error value "Class-Type mismatch" (see [RFC2205]). 8. Security Considerations This document introduces no new security considerations to [RFC3473]. GMPLS security is described in Section 11 of [RFC3471] and refers to [RFC3209] for RSVP-TE. Further details of MPLS-TE and GMPLS security can be found in [RFC5920]. 9. IANA Considerations IANA maintains registries and sub-registries for RSVP-TE as used by GMPLS. IANA has made allocations from these registries as set out in the following sections. 9.1. RSVP Objects Class Types This document introduces two new Class Types for existing RSVP objects. IANA has made allocations from the "Resource ReSerVation Protocol (RSVP) Parameters" registry using the "Class Names, Class Numbers, and Class Types" sub-registry. Class Number Class Name Reference ------------ ----------------------- --------- 9 FLOWSPEC [RFC2205] Class Type (C-Type): 6 Ethernet SENDER_TSPEC [RFC6003] Class Number Class Name Reference ------------ ----------------------- --------- 12 SENDER_TSPEC [RFC2205] Class Type (C-Type): 6 Ethernet SENDER_TSPEC [RFC6003] 9.2. Ethernet Switching Granularities IANA maintains a registry of GMPLS parameters called "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Parameters". IANA has created a new sub-registry called "Ethernet Switching Granularities" to contain the values that may be carried in the Switching Granularity field of the Ethernet SENDER_TSPEC object. Values are as follows: 0-2 See below. 3-239 Unassigned 240-254 Reserved for Vendor-Specific Use 255 Reserved 256-65535 Not assigned at this time The registration procedure is Standards Action. Initial entries in this sub-registry are as follows: Value Switching Granularity Reference ----- -------------------------------------- ------------------ 0 Provided in signaling. [RFC6003][RFC6004] 1 Ethernet Port (for port-based service) [RFC6003] 2 Ethernet Frame (for EVC-based service) [RFC6003] 255 Reserved [RFC6003] 9.3. Ethernet Sender TSpec TLVs IANA maintains a registry of GMPLS parameters called "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Parameters". IANA has created a new sub-registry called "Ethernet Sender TSpec TLVs / Ethernet Flowspec TLVs" to contain the TLV type values for TLVs carried in the Ethernet SENDER_TSPEC object. Values are as follows: 0-3 See below. 4-239 Unassigned 240-254 Reserved for Vendor-Specific Use 255 Reserved 256-65535 Not assigned at this time The registration procedure is Standards Action. Initial entries in this sub-registry are as follows: Type Description Reference ----- -------------------------------- --------- 0 Reserved [RFC6003] 1 Reserved [RFC6003] 2 Ethernet Bandwidth Profile [RFC6003] 3 Layer 2 Control Protocol (L2CP) [RFC6003] 255 Reserved [RFC6003] 9.4. Ethernet Bandwidth Profiles IANA maintains a registry of GMPLS parameters called "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Parameters". IANA has created a new sub-registry called "Ethernet Bandwidth Profiles" to contain bit flags carried in the Ethernet Bandwidth Profile TLV of the Ethernet SENDER_TSPEC object. Bits are to be allocated by IETF Standards Action. Bits are numbered from bit 0 as the low order bit. Initial entries are as follows: Bit Hex Description Reference --- ---- -------------------------- ------------- 0 0x01 Coupling Flag (CF) [RFC6003] 1 0x02 Color Mode (CM) [RFC6003] 10. Acknowledgments Many thanks to Adrian Farrel for his comments. Lou Berger provided the input on control traffic processing. 11. References 11.1. Normative References [MEF10.1] The MEF Technical Specification, "Ethernet Services Attributes Phase 2", MEF 10.1, November 2006. [RFC2205] Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S. Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional Specification", RFC 2205, September 1997. [RFC2210] Wroclawski, J., "The Use of RSVP with IETF Integrated Services", RFC 2210, September 1997. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, December 2001. [RFC3471] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description", RFC 3471, January 2003. [RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol- Traffic Engineering (RSVP-TE) Extensions", RFC 3473, January 2003. [RFC4124] Le Faucheur, F., Ed., "Protocol Extensions for Support of Diffserv-aware MPLS Traffic Engineering", RFC 4124, June 2005. [RFC4506] Eisler, M., Ed., "XDR: External Data Representation Standard", STD 67, RFC 4506, May 2006. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC6004] Berger, L. and D. Fedyk, "Generalized MPLS (GMPLS) Support for Metro Ethernet Forum and G.8011 Ethernet Services", RFC 6004, October 2010. 11.2. Informative References [ETHv2] Digital, Intel, and Xerox, "The Ethernet -- A Local Area Network: Data Link Layer and Physical Layer Specifications", Version 2.0, November 1982. [IEEE802.3] IEEE 802.3 LAN/MAN CSMA/CD (Ethernet) Access Method, IEEE Standard for Information technology- Specific requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CMSA/CD) Access Method and Physical Layer Specifications, IEEE 802.3-2008. [MCOS] Minei, I., Gan, D., Kompella, K., and X. Li, "Extensions for Differentiated Services-aware Traffic Engineered LSPs", Work in Progress, June 2006. [MEF6] The Metro Ethernet Forum, "Ethernet Services Definitions - Phase I", MEF 6, June 2004. [MEF10.2] The MEF Technical Specification, "Ethernet Services Attributes Phase 2", MEF 10.2, October 2009. [RFC5920] Fang, L., Ed., "Security Framework for MPLS and GMPLS Networks", RFC 5920, July 2010. Author's Address Dimitri Papadimitriou Alcatel-Lucent Bell Copernicuslaan 50 B-2018 Antwerpen, Belgium Phone: +32 3 2408491 EMail: dimitri.papadimitriou@alcatel-lucent.be